WhatsApp

Article

The unglamorous water rule that makes turbine inlet cooling pay

beta-pramesti-asiaindustry-power-generation-combinedprocess-ccgt

One Wrong Drop, Turbine Output Plummets: A Guide to TIAC Water Treatment at PLTGU

Gas turbine fogging is only safe with ultra‑pure demin water; an evaporative cooler needs a cooling-tower-style chemical program. Without that, compressor blades foul quickly and performance drops.

When ambient temperature rises, large gas turbines can lose about 20% of their power at 35 °C (inlet fogging climate analysis; 0.9% for every 1 °C rise), according to ResearchGate. The solution is TIAC (turbine inlet air cooling, cooling the turbine inlet air) technology such as fogging, which can cool the air by up to ~21°F (≈12 °C) under ambient conditions of 96°F (≈36 °C), writes turbineinletcooling.org.

But there is a hard requirement: every mineral in the fogging water will end up on the compressor blades. That means only ultra‑clean demineralized water may enter—otherwise, efficiency collapses and maintenance costs soar, Efficient Plant and turbineinletcooling.org stress. A technical article in Power Engineering reviews the scope of its use in the field.

Ultra‑pure water quality for fogging

Fogging (injection of a fine water mist to cool the inlet air) must use ultra‑clean demineralized water because “every mineral/particulate will concentrate on the compressor blades”, Efficient Plant and turbineinletcooling.org note. Common industry practice requires TDS (total dissolved solids, the amount of dissolved solids) < 1 ppm with conductivity ≈ 2 µS/cm (Efficient Plant).

Hardness, silica, and salts will precipitate into scale and narrow the flow area, according to turbineinletcooling.org, which ultimately lowers efficiency. Field reports show a power drop of ~2–4% after 3,000 hours when particulate filtration is “only moderate,” writes Pipeline & Gas Journal. With deionized water feed, fouling can be prevented (Efficient Plant), so room for output recovery of up to ~20% at high temperature remains open (large turbines lose ~20% power at 35 °C; ResearchGate).

Fogging water purification train

In practice, a fogging system requires its own ultra‑pure make‑up loop: sand filtration, reverse osmosis, and a mixed‑bed deionizer to remove hardness, silica, and organics (Efficient Plant). For the sand filtration stage, media such as sand silica dual media are commonly used as pretreatment. A multi-stage train like this is a form of industrial water demineralization that we build for feedwater needs with very low conductivity.

The RO unit (reverse osmosis, separation with a pressurized membrane) is the backbone of TDS reduction; a brackish water RO system is commonly used to produce low-salt permeate before deionization polishing. The pressure, flow rate, and temperature of these RO and UF units can be read through an RO and UF monitoring system.

To achieve very low conductivity, polishing mixed‑bed (mixed‑bed deionizer) is used. All wetted piping and nozzles must be stainless steel or plastic; iron/galvanized fittings will corrode or trigger scale deposition (Efficient Plant).

Bacteria can still grow in stagnant demin water. For this reason, many systems use automatic nightly blowdown and periodic “bleed‑and‑fill” (partial drain and refill) to prevent biofilm in the nozzle lines—and to reduce the risk of nozzle plugging (Efficient Plant). The key point is that following OEM guidance to supply only pure water (often equivalent to distilled/DI grade) is crucial: demin feed prevents mineral deposits and corrosion in the compressor and hot section (Efficient Plant; turbineinletcooling.org). Ignoring this can trigger fouling or pitting on the blades, disrupting flow and the material's fatigue life (Structural Integrity).

Evaporative cooler and chemical program

Unlike fogging, which tends to be “closed”, an evaporative inlet cooler (wetted‑media; media are wetted) uses recirculating water that concentrates dissolved salts. Without treatment, hard water quickly forms scale in the media/fill and downstream channels and promotes algae/bacteria. For this reason, facilities use a cooling-tower-style water treatment program: scaling, corrosion, and biological control (water.co.id)—which is available in our catalog as an industrial cooling tower chemical program.

Scale control includes maintaining cycles‑of‑concentration at 3–8× (the ratio of dissolved solids concentration in the circulation to make‑up water) through blowdown (controlled discharge), and adding scale inhibitor/coagulant to inhibit precipitation of calcium carbonate/silicate. A CaCO₃ layer only 0.75 mm thick can raise the energy penalty by ~27%, so dosing phosphonate or polycarboxylate is standard practice. Industry guidance in Indonesia also emphasizes adding scale inhibitor to disrupt mineral crystallization (water.co.id)—see our cooling tower scale inhibitor.

For water efficiency, high concentration reduces make‑up demand, but increases scaling risk if not controlled. A common practice is conductivity-based blowdown to keep TDS below the inhibitor threshold. Stable chemical dosing requires injection accuracy; a dosing pump helps keep the chemical residual constant.

Chemical components for evaporative inlet coolers are usually adopted from the cooling tower package; our industrial cooling tower chemical program covers scale, corrosion, and microbiological control in one integrated program.

Corrosion and biological growth control

Corrosion on wet metal surfaces is prevented with neutralizing/filming corrosion inhibitors that form a protective film—a practice set out in cooling tower water treatment guidance (water.co.id). Corrosion inhibitor formulations are used to maintain the integrity of pipes and casing.

Biological growth—including Legionella risk—is controlled with biocides (oxidizing agents such as chlorine/bromine or non‑oxidizing agents such as isothiazolinone) to maintain a continuous disinfectant residual, as stated by CDC and water.co.id. A typical residual target is ~0.5–2 ppm Cl₂ equivalent, with periodic shock/chlorine‑bromine spikes (CDC). Biofilm thermal conductivity is only ~0.2, far below CaCO₃ (6.4), so biofilm can also cripple heat transfer—making effective biocide use mandatory. Biocide packages for cooling towers are usually used on recirculating inlet coolers.

Routine maintenance and monitoring

Coils and media/fill are cleaned/rotated on schedule; dosing rate, blowdown cycle, and microbial counts are monitored. Without water management, corrosion and fouling can be 5–10× worse than in a treated system, and are “responsible for downtime, equipment damage, and increased energy consumption”.

TIAC performance summary

In short, turbine inlet air cooling requires strict stewardship of water quality. For fogging, only ultra-pure demineralized water (sub-ppm TDS) may be injected (Efficient Plant; turbineinletcooling.org). For evaporative inlet coolers, apply cooling tower discipline: controlled blowdown, scale/corrosion inhibitors, and biocide/disinfectant to prevent biological fouling (CDC; water.co.id). These steps prevent compressor fouling and heat-transfer loss, ensuring TIAC restores lost peak power potential of up to ~20% (ResearchGate; Structural Integrity) without unplanned outage.

Sources and technical references

Best practice & manufacturer guidelines: Efficient Plant; turbineinletcooling.org; Efficient Plant. Compressor fouling studies: Pipeline & Gas Journal; Structural Integrity. Power‑boost analysis: ResearchGate; Power Engineering. Legionella and biocide control: CDC; water.co.id.